Barudan Logo  

Please enter a search term to begin your search.

 

V Series Updates

 V-Series Multi Head: VS/VY machines

Current release (VS 3.00 R00) 

Highlights of VS 3.00 R00 changes:

  • Added Spanning Tree Function for network.
  • Added Tie-Off Stitch Function before trimming.

Highlights of V2.90 R01 changes:

When using DFS COM protocol mode, Memory location #30 acts like ABC mode for downloading designs.
Example:  When memory #30 is selected, the downloaded design overwrites the previous design in this location.
Note: You must be out of Drive mode to overwrite the previous design.

Highlights of V2.90 R00 changes:

When using DFS COM protocol mode, Memory location #30 acts like ABC mode for downloading designs.
Example:  When memory #30 is selected, the downloaded design overwrites the previous design in this location.
Note: You must be out of Drive mode to overwrite the previous design.Highlights of V2.80 R00 changes:

• D16 Bobbin Break code activated for LEM Reports
• LAN Board Version 6.9.0.2 Compatibility
• Added MAC address to network settings
• Added DHCP to network settings

VSB300R0.zip for CF Card installation 
VSB.zip  for Floppy Disk installation 

This software is for Barudan "V" series machines with more than one sewing head. Specific model numbers include:

  • BEVY-Z1502C
  • BEVY-Z1504C
  • BEVY-Z1506C
  • BEVY-Z1508C
  • BEVS-Z1512C
  • BEVS-Z1515C 

Instructions for installing VS/VY series machine software from a CF card:

  1. Download the system software zip file above, and save on your computer's hard disk.
  2. Unzip the system software file.
  3. Create a new folder on the CF card named SYSTEM.
  4. Copy the system software file (*.sys) to the SYSTEM folder you just created.
  5. Turn the power OFF at the Automat.
  6. Insert the CF card with the new system software on it.
  7. Press and hold the Read key, while powering ON (on the Automat) until you see the "System Version" Screen.
  8. Press and hold the Memory key to read the system files.
  9. Select the correct system file to load by using the Jog keys, then press and hold the Execute key for 5 seconds to start the update process.
  10. After the update completes, seek origin as you normally would upon power-on.

Instructions for installing VS/VY series machine software from a floppy disk:

  1. Download the "VSB.ZIP" file above, and save it to your hard drive.
  2. Unzip the system software file.
  3. Label a blank, formatted floppy disk:
                   VS/VY System Disk
                   Version [####]
  4. Copy the "VSB.SYS" file from your hard disk to the floppy disk
  5. Turn the power OFF at the Automat.
  6. Insert the floppy disk with the new system software on it.
  7. Press and hold the Read key, while powering ON (on the Automat) until you see the "System Version" Screen.
  8. Press the Read key to start the update process. Update takes a few minutes.
  9. After the update completes, seek origin as you normally would upon power-on.


printer-friendly V Series Updates page
 

V- Series Single Head: VT machines 

Current release  VT 4.00 R00 

Highlights of VT 4.00 R00 changes:

  • Added Spanning Tree Function for network.
  • Added Tie-Off Stitch Function before trimming.

Highlights of VT 3.70 R01 changes:

When using DFS COM protocol mode, Memory location #30 acts like ABC mode for downloading designs.
Example:  When memory #30 is selected, the downloaded design overwrites the previous design in this location.
Note: You must be out of Drive mode to overwrite the previous design.

Highlights of VT 3.60 R01 changes:

• D16 Bobbin Break code activated for LEM Reports
• LAN Board Version 6.9.0.2 Compatibility
• Added MAC address to network settings
• Added DHCP to network settings
• CII S-Head enhancement for running high speed

VTB400R0.zip -  for these models:

  • BEVT-S901CAII Elite XLII
  • BEVT-Z901CA Elite XL
  • BEVT-Z1501CB Elite Pro
  • BEVT-Z1501CB II Elite Pro II
  • BEVT-Z1501C Single-Head
  • BEVT-Z1501C II Single Head 

Instructions for installing VT series machine software:

  1. Download the system software zip file above to your computer's hard drive.
  2. Unzip the system software file.
  3. Create a new folder on the CF card / USB Drive named SYSTEM.  
  4. Save the software system file (*.sys) to the SYSTEM folder you just created. 
  5. Turn the power OFF at the Automat.
  6. Insert the CF card / USB Drive with the new system software on it 
  7. Press and hold the Start button, while powering ON (on the Automat)  
  8. The "System Version" Screen will appear 
  9. Press and hold the Start button again, to display the CF System screen and read the system files from the CF card
  10. If more than one system file is listed, select the correct file to load by using the Jog keys
  11. Then press and hold the Execute key for 5 seconds to start the update process 
  12. After the update completes, seek origin as you normally would upon power-on

Machine Sales: 800-627-4776 Calendar | Privacy/Copyright | Site Map | Visit Barudan Worldwide Right from the start.